Mellanox network cable MCP4Y10-N002 DAC Cable IB Twin Port NDR up to 800Gb/s 2m

mellanox network cable MCP4Y10-N002 DAC Cable IB Twin Port NDR up to 800Gb/s 2m

MCP4Y10-N002 is an 2x400Gb/s twin-port OSFP (Octal Small Formfactor Pluggable) to 2x400Gb/s twin-port OSFP Direct Attached. Copper cable (DAC).DAC cables are the lowest-cost, lowest-latency, near zero power consuming, high-speed links available due to their simplicity of design and minimal components. Using the Octal Small Formfactor Plug (OSFP) and containing eight high-speed electrical copper pairs, each operating at data rates of up to 100Gb/s.

The DAC firmware supports both InfiniBand and Ethernet and is automatically enabled depending on the protocol of the switch attached to. EEPROMs provide product configuration information to be read by the host. Every cable length is tuned to reduce internal signal noise and back reflections.

MCP4Y10-N002 Specifications

Model number	Description
MCP4Y10-N00A	NVIDIA passive copper cable, IB twin port NDR, up to 800Gb/s, OSFP, 0.5m
MCP4Y10-N001	NVIDIA passive copper cable, IB NDR, up to 800Gb/s, OSFP, 1m
MCP4Y10-N01A	NVIDIA passive copper cable, IB NDR, up to 800Gb/s, OSFP, 1.5m
MCP4Y10-N002	NVIDIA passive copper cable, IB NDR, up to 800Gb/s, OSFP, 2m

MCP4Y10-N002 Key Features

2x400Gb/s data rate

Based on 8-channels of 100G-PAM4 modulation

0.5, 1, 1.5, and 2- meter lengths

SFF-8665 compliant

Operating case temperature 0-70°C Single 3.3V supply voltage

Hot pluggable

RoHS compliant

LSZH (Low Smoke Zero Halogen) jacket

LF (Lead Free) HF (Halogen Free) PCB

OSFPxmsa.org based

SFF-8636 compliantI 2C management interface

Applications

2x400Gb/s

Quantum-2

InfiniBand or

Spectrum-4 Ethernet

switch-to-switch and

switch-to-DGX-H100

The main use for the MCP4Y10 is to link together two twin-port, OSFP-based Quantum-2 InfiniBandor Spectrum-4 Ethernet switches to each other up to 2-meters with both ends being finned-topconnectors. OSFP flat top (designated -FLT in the part number) cable ends are available for liquidcooled switches and DGX H100 systems with a flat top for the DGX H100 and finned top connectorfor the InfiniBand or Ethernet switch. Thin 30AWG wire gauge is used for 0.5m to 2m for easybending.

Regulatory Compliance and Classification

• Safety: CB, TUV, CE, EAC, UKCA
• EMC: CE, FCC, ICES, RCM, VCCI

Ask your NVIDIA FAE for a zip file of the certifications for this product.FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference when the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in whichcase the user will be required to correct the interference at his own expense.mellanox network cable

Cabling Information

Handling Precautions and Electrostatic Discharge (ESD)The cable is compatible with ESD levels in typical data center operating environments and certifiedin accordance with the standards listed in the Regulatory Compliance Section. The product isshipped with protective caps on its connectors to protect it until the time of installation. In normalhandling and operation of high-speed cables and optical transceivers, ESD is of concern duringinsertion into the QSFP cage of the server/switch. Hence, standard ESD handling precautions mustbe observed.